Before you hire anyone to clean your siding, ask six things. What is my siding, and how will you clean it? What pressure will you use? How will you protect my plants and the house? What exactly is included? How does the job end? And can I see your insurance? A good company answers each one in plain words, for your house, and puts the answers in the quote.
Key Takeaways
- The company should name your siding type and change its method to match
- Siding gets a soft wash at low pressure; high pressure is a last resort on any surface
- Ask how plants are protected and how many times they get rinsed
- Get the list of what is included in writing: trim, soffits, porch ceilings, windows
- The job should end with a walk around the house with you
Why the Questions Matter
Most siding damage from cleaning comes from one cause: the wrong method for the material. Too much pressure on vinyl, stucco, or painted wood drives water into the wall or takes the paint off. You cannot see that on the day of the job. It shows up months later as peeling paint, stains, or soft trim.
You do not need to know how to clean siding to hire well. You need to ask the questions below and listen for answers about your house in particular. If an answer sounds the same for every house, ask again.
1. What Is My Siding, and How Will You Clean It?
A good company names the material before it names a price. Here is what a good answer sounds like for the common types around Philadelphia and the Main Line.
Vinyl: soft washed. A cleaning solution kills the algae and mildew, and a low-pressure rinse takes it off. No scrubbing.
Painted wood clapboard: soft washed, with care to clean the paint film without lifting it.
Cedar: soft washed, then given time to dry. Wet cedar on a shaded wall needs warm, moving air.
Fiber cement: soft washed. It is painted, and the joints are caulked, so it gets the same care as painted wood.
Stucco and EIFS: soft washed, after a check for cracks and open seams. EIFS is a thin coat over foam and holds water where it is broken.
Stone or brick with lime mortar: low pressure, with the solution mixed for the mortar. High pressure pulls soft lime mortar out of the joints.
Aluminum: it oxidizes into a chalky layer. It cleans well with the right solution, but hard scrubbing leaves shiny patches.
If the company cannot tell you what your siding is, or gives one method for all of it, keep looking.
See also: What Is Soft Washing a House? · How to Clean Vinyl Siding Without Scrubbing · Clean Cedar Siding Without Trapping Moisture
2. What Pressure Will You Use?
On siding, the answer should be low. We soft wash siding: the solution does the cleaning, and the rinse is close to garden-hose pressure.
On hard surfaces like a concrete walk or a stone step, a good crew still starts at low pressure, then goes to medium only if the dirt does not come off. High pressure is a last resort on any surface, because it can be destructive.
Ask what they do when one spot will not come clean. A good answer is more dwell time for the solution, or a second application. A bad answer is to turn up the pressure on the siding.
See also: Soft Washing vs. Pressure Washing
3. How Will You Protect My Plants and the House?
Ask for the steps. A good answer: beds and shrubs next to the house get wet down before the solution goes on, delicate plants get covered, and everything gets rinsed again at the end. Runoff goes to the grass and beds, not into a storm drain.
For the house itself, ask how they handle windows, vents, outdoor outlets, and light fixtures. The rinse should go with the siding, top down, never up under the laps.
Ask what you need to do. Usually that means closing the windows, keeping pets inside during the work and for about an hour after, and moving cars and furniture away from the walls. Our yard prep guide has the full list.
4. What Exactly Is Included?
"Wash the house" can mean a lot of things. Ask for a list, and get it in the quote.
The walls: all sides, or only the dirty side? A wash on one side often makes the other sides look worse.
Trim, soffits, fascia, and shutters: these are part of a full house wash, but ask.
Porch ceilings and overhangs: algae and webs collect here, and some quotes leave them out.
Gutters: the outside face of the gutter is different from clearing out the inside. Ask which one, if either.
Windows, screens, decks, walks, and the driveway: usually separate items. Ask for each one by name.
Ask what will not come off. Rust stains, artillery fungus spots, and paint that is already failing are common examples. A company that tells you this before the job is being honest with you.
5. How Does the Job End?
Ask if the crew walks the house with you before they leave. It should be a yes. You want to look at every side with them while the equipment is still there, so any missed spot gets done on the day of the job.
After every job, our crew walks the property with the client to make sure it is clean before we pack up. If something is not right, we fix it then.
Also ask what happens if you see a streak or a missed spot after the walls dry. Get that answer in writing.
6. Can I See Your Insurance?
Ask for a certificate of liability insurance. It costs a real company nothing to send. If something goes wrong with a window or a light fixture, it is the difference between an easy fix and a fight.
Ask who will actually be at your house, and whether the person who quoted the job will be on site or reachable that day.
Ask Us These Questions
We clean siding across Philadelphia and the Main Line. We will name your siding, tell you how we will clean it, and list what is included. We quote within 24 hours. Text a photo of the house, or call (610) 981-2285.
See also: House washing · What to Expect From a Home Cleaning Assessment · Request a quote
