Clean a house exterior from the top down: the roof first, then the gutters, then the siding and trim, then the windows, and the patio, walkways and driveway last. Everything you rinse off a surface runs down onto the surfaces below it. In this order, each surface gets cleaned once, and nothing you finished gets dirty again from the work above it.
Key Takeaways
- Roof first. The rinse sends dead growth and grit into the gutters and over the walls
- Gutters second, so you clear out what came off the roof as well as the leaves
- Siding third. Gutter work and roof runoff mark the walls, so wash them after
- Windows fourth. The wall wash runs over the glass, so the glass waits until the walls are done
- Hardscape last. The patio and driveway catch the runoff from every step above
The order, and the reason for it
Water and dirt move down. If you clean the patio on Saturday and the siding the next week, the siding rinse lands on the clean patio. If you wash the walls before the gutters are cleared, the next storm spills gutter sludge down the clean wall.
So the order follows gravity:
1. Roof
2. Gutters and downspouts
3. Siding, trim, soffits and porch ceilings
4. Windows, frames and screens
5. Patio, walkways, steps, pool deck and driveway
Before step one, soak the plants and beds near the house with plain water. Rinse them again after each step that uses a cleaning solution.
1. The roof
The roof is the highest surface, so it goes first. We soft wash shingle roofs: a cleaning solution at low pressure kills the black algae streaks and the moss, and a low-pressure rinse follows. Never pressure wash shingles. High pressure strips the granules that protect the shingle from the sun.
Everything that comes off the roof goes somewhere lower: dead algae, moss, loose granules and solution. Most of it goes into the gutters. Some of it runs over the edge onto the walls and the plants. That is the reason nothing below the roof should be cleaned first.
On steep and low-slope roofs, we soft wash by drone. The drone sprays from a nozzle fed by a hose from our ground equipment, so nobody walks on the shingles and no ladder leans on the gutters. On a flat roof, the crew works on the roof itself.
See also: Roof cleaning · Roof moss removal
2. The gutters
Clean the gutters after the roof, not before. The roof wash puts moss, granules and dead growth into the trough. If the gutters were cleared first, they now need it again.
Clearing a gutter also makes a mess below it. Wet debris drips over the edge, and a downspout flush pushes dark water out at the bottom. Those marks land on siding that is still to be washed, which is fine at this stage.
The gutters also explain a lot of wall stains. A narrow green or black band under one point of the gutter means it overflows there. Clear it and check it before the wall below it is washed, or the band comes back after the next storm.
See also: Gutter cleaning · When gutters start damaging your exterior
3. The siding and trim
With the roof and gutters done, nothing above the walls is left to drip on them. Now the siding, trim, soffits and porch ceilings get washed.
Most siding gets a soft wash. We put the solution on from the bottom of the wall up, so it does not run in streaks over dry dirt, let it sit for a few minutes, and rinse from the top down. Where a surface can take pressure, such as bare brick or a concrete foundation, we start at low pressure and go to medium only if the dirt does not move. High pressure is a last resort on any surface.
The siding rinse runs over the windows and down onto the walks and the patio. Both of those are still to come.
See also: House washing · What is soft washing?
4. The windows
Windows come after the walls. Solution and rinse water from the siding run over the glass and dry as spots. Clean the glass first and you clean it twice.
The windows follow the same top-down rule on their own. On a two- or three-story house, we clean the upper windows by drone first. The glass is soft washed or pressure washed, depending on the glass, and the pressure wash uses pressurized deionized water, at most about 2,500 PSI on glass. Then we clean the lower floors with a water-fed pole and deionized water. Deionized water has the minerals taken out, so it dries without spots.
Frames, sills and tracks get rinsed in the same pass. They collect grit and pollen that would run onto clean glass in the next rain.
See also: Window washing
5. The patio, walkways and driveway
Hardscape goes last because it is at the bottom. Roof runoff, gutter debris, siding solution and window rinse all land on it. Cleaning it earlier means cleaning it again.
Concrete and pavers can take more pressure than siding, so this is where pressure washing does most of the work. We still start at low pressure and go to medium where needed. High pressure is a last resort, and softer stone such as bluestone and flagstone stays lower still. We treat green growth on shaded patios and walks with a cleaning solution first, so the pressure only has to remove growth that is already dead.
If you plan to seal pavers or re-sand the joints, that comes after the cleaning, once the surface is fully dry.
See also: Patio and walkway washing · Brick paver cleaning and sealing, in order
If you split the work across visits
You do not have to do everything on one day. If you book the work in parts, keep the same order across the visits: roof and gutters before the house wash, the house wash before the windows, and the patio and driveway last.
The one step that often moves is the fall gutter cleaning, which waits until the leaves are down. If the gutters overflowed onto the walls over the summer, clear them before the house wash and plan another gutter visit after leaf drop.
At the end of the job
When the last surface is rinsed, we rinse the plants one more time. Then we walk the property with you, top to bottom, to confirm every surface is clean.
Text a photo of the house to (610) 981-2285 and tell us which parts you want cleaned. We reply with a quote within 24 hours.
See also: Request a quote · How to prepare your yard before house washing
